Las fallas de la válvula y su análisis de causa (primera parte)

Dec 27, 2021
Fallos de válvulas y análisis de causas
1.Fugas
Las fugas se dividen principalmente en fugas externas y fugas internas. Las fugas externas se refieren principalmente al fluido que fluye hacia el exterior del sistema debido a fallas de sellado y otras razones, mientras que el fluido que fluye hacia el interior del sistema se denomina fuga interna. La razón principal de la fuga delválvulaes la falla de sellado. Fuga la válvula de una turbina de vapor de 300MW en una central térmica. Después de realizar una inspección completa, se encontró que el asiento de la válvula estaba desgastado debido a múltiples aperturas y cierres, lo que condujo a una disminución en el rendimiento de sellado de la válvula, y se produjo una fuga porque la válvula no se cerró bien. En un entorno de baja temperatura, a medida que la temperatura disminuye, las propiedades de tracción y compresión del caucho disminuirán drásticamente y se endurecerán, lo que conducirá a una reducción en la fuerza de preapriete de la superficie de contacto, lo que provocará fugas. En condiciones de alta temperatura y alta presión, el cuerpo de la válvula se deformará y el vástago de la válvula puede caerse y atascarse. Independientemente de las condiciones de trabajo, una vez que el sellado de la válvula falla y provoca fugas, especialmente cuando se trata de medios de alta temperatura, alta presión, corrosivos, radiactivos, inflamables y explosivos, pueden ocurrir accidentes como envenenamiento, incendio, explosión y lesiones personales. ocurrira. La Tabla 1 muestra las ubicaciones de fugas comunes y las causas de la válvula.
 
Tabla 1 Ubicaciones comunes de fugas de válvulas y sus razones
Leakage parts Sealing surfaces  Packing Sealing rings  Valve bodies and bonnets
Reasons for leakages  ①The sealing surface is uneven due to the production material or great force.
②The valve stem is bent and the assembly position is deflected.
③The selection is not according to the requirements.
①The packing is not selected according to the requirements or is aging, which causes the sealing performance to decrease.
②The problem of the valve stem causes the packing to be damaged.
 
①The sealing ring is not selected according to requirements, and the material has poor fatigue resistance.
② The sealing ring is corroded and there is a problem with the heat treatment.
 
①The bolts and fasteners are loose or the tightness is different.
② There is insufficient strength for materials or a defect in the processing technology.
 
 
The reasons for leakages of valves caused by sealing failure are as follows:
(1) Unreasonable design
It is found that the fatigue life of the steam drum continuous exhaust valve is prolonged with the decrease of load, the improvement of surface finish and good heat treatment after using ANSYS and MSC.Fatigue to simulate. The results obtained by the analysis were consistent with the basic common sense of engineering, which verified the feasibility of using analysis software to analyze the fatigue life of the continuous exhaust valve. Finite element analysis was performed for the bellows and a valve model with leakage was established. It was calculated that when the surface roughness Ra value was between 0.1 and 0.4μm, it not only met the requirement for the service life, but also solved the problem of the leakage of the valve.
 
(2) Unreasonable structure
The sealing structure of the slag lock valve is designed based on the working environment, sealing specific pressure and structural sizes, as shown in Figure 1. The finite element model was established for simulation, and the flow model and leakage model were used for analysis. The effective sealing interval of the design parameters and the valve seat leakage level under different parameters were obtained and verified. After analyzing the U-shaped sealing (Figure 2), it is found that the maximum creep strain occurred at the upper and lower arm spans of the U-shaped sealing and the root of the U-shaped groove, and there was no leakage.

 
Figure 1 The sealing structure of the slag lock valve
 
 
Figure 2 The U shape sealing structure
 
(3) Unreasonable selection of materials
A439D-2C austenitic ductile iron was trial-produced, and its mechanical properties and composition are shown in Table 2 and Table 3. The spheroidization rate of austenitic ductile iron is higher than 95%, and its mechanical properties and composition are better than those of the same type of cast iron in China; its plasticity index is increased by 3 times. After the material was applied to the double-sided sealing structure, the service life of the valve was significantly improved, and the manufacturing cost and difficulty were reduced. A cobalt-free iron-based alloy powder was researched and developed and was covered on the stainless steel substrate by the laser cladding technology. The hardness of the stainless steel substrate covered with the powder was significantly increased after testing, which was about twice the hardness of the uncovered substrate.
 
Table 2 Mechanical properties of austenitic ductile iron
Items The tensile stress in tensile strength/MPa Elongation at the break at non-proportional elongation/% Elastic modulus/GPa Tensile stress at yield (offset 0.2%)/MPa Loads at tensile strength/kN
1 507.236 31.602 93.145 259.286 9.255
2 464.776 21.091 109.142 235.615 9.126
3 478.537 33.006 95.900 235.504 9.396
                  
Table 3 The composition of austenitic ductile iron wt%
Technical standards C Si Mn P Cr Ni
ASTM Less than and equal to 2.90 Between 1.00 and 3.00 Between 1.80 and 2.40 Less than and equal to 0.08 Less than and equal to 0.05 Between 21.00 and 24.00
 
A large number of scholars have analyzed and improved the sealing structure of the valve from the perspectives of design, structure and materials, but there are still problems. First, the sealing is qualitatively analyzed under specific conditions and the calculation method for quantitative analysis can't be performed for most conditions. Second, sealing involves many microscopic in the working environment, and the principles and manifestation of microscopic phenomena caused by different influencing factors are not the same. Therefore, it is very important to study the sealing failure caused by multiple factors, which can provide directions and ways to further improve the sealing structure and improve the sealing performance.
 
2. Broken valve bodies
The main reasons for the breaking of the valve body are as follows:
(1) Improper selection of materials for valve bodies or material defects such as sand holes, bubbles, shrinkage holes, etc.
When a wafer butterfly valve is installed, if rubber gaskets or other gaskets are provided to increase the sealing surface of the valve body end, it will cause cracking and breaking in the valve body during use. The force, material, torque and other aspects of the valve body in this state were analyzed. It is believed that the valve body's material should be ductile iron, and no defects are allowed to ensure the normal use and safe operation of the valve body. The impact of casting defects on the strength of hydraulic valve bodies was analyzed. The ProCAST software was used to establish a casting defect model, and the stress values of the valve body in the ideal state and defective state under different pressures were compared. It is found that the valve body with shrinkage holes would produce more partial stress, as shown in Figure 3, that is, shrinkage would cause the partial effective wall thickness of the valve body to be reduced. Stress concentration would occur, which would lead to a decrease in the load-bearing capacity of the valve body and strength, and a significant decrease in fatigue and service life.
 
 
Figure 3 The curve of the greatest stress changing with the pressure
 

next: Las fallas de la válvula y su análisis de causa (segunda parte)

previous: Soluciones a Fallas de Válvulas


Sobre el autor
Teresa
Teresa is a skilled author specializing in industrial technical articles with over eight years of experience. She has a deep understanding of manufacturing processes, material science, and technological advancements. Her work includes detailed analyses, process optimization techniques, and quality control methods that aim to enhance production efficiency and product quality across various industries. Teresa's articles are well-researched, clear, and informative, making complex industrial concepts accessible to professionals and stakeholders.

Sobre nosotros

Disponemos de una fundición y varios centros de mecanizado. Después de más de 30 años de innovación y desarrollo, nos hemos convertido en una fábrica que integra diseño, investigación y desarrollo, fabricación y ventas. Hay más de 500 empleados, incluidos casi 200 trabajadores de I + D y tecnología. Contamos con un taller de producción profesional, un conjunto completo de centros de mecanizado CNC a gran escala, centros de mecanizado horizontal automatizados, tornos verticales de pórtico a gran escala, máquinas de soldadura automática y una línea de producción completa.

Useful Links

Contact

sales@medvalves.com

086 592 5819200

Xiamen, P. R. China